Third Party Press

1917 dwm

rockisle1903

Senior Member
Just picked this one up. It is a stamped matching to the screws, non depot, with matching rod..It has a two piece beech stock that is starting to have some separation issues probably due to being stored a place with extreme temperature swings such as an attic or unheated basement...Cant' get one of the TG screws out for the barrel code, soaking in Kroil as I type..A nice honest example..Comments welcome, thanks for looking, Mike
 

Attachments

  • 1917dwm 001.jpg
    1917dwm 001.jpg
    113.1 KB · Views: 53
  • 1917dwm 003.jpg
    1917dwm 003.jpg
    91.8 KB · Views: 65
  • 1917dwm 002.jpg
    1917dwm 002.jpg
    125.6 KB · Views: 52
  • 1917dwm 005.jpg
    1917dwm 005.jpg
    91.5 KB · Views: 46
  • 1917dwm 004.jpg
    1917dwm 004.jpg
    94.8 KB · Views: 45
  • 1917dwm 006.jpg
    1917dwm 006.jpg
    119.5 KB · Views: 52
  • 1917dwm 007.jpg
    1917dwm 007.jpg
    90 KB · Views: 38
  • 1917dwm 008.jpg
    1917dwm 008.jpg
    114.4 KB · Views: 39
  • 1917dwm 009.JPG
    1917dwm 009.JPG
    279 KB · Views: 37
  • 1917dwm 010.jpg
    1917dwm 010.jpg
    91.9 KB · Views: 41
  • 1917dwm 011.jpg
    1917dwm 011.jpg
    140.1 KB · Views: 36
  • 1917dwm 012.jpg
    1917dwm 012.jpg
    96.9 KB · Views: 34
  • 1917dwm 013.jpg
    1917dwm 013.jpg
    99.7 KB · Views: 39
  • 1917dwm 014.jpg
    1917dwm 014.jpg
    104.4 KB · Views: 45
Nice, honest old rifle! I've had good luck on those heavily coating Break-Free on the action and components and putting soaked cleaning patches over the solution to hold it in place for a day or two, depending on temperature. Then a vigorous rub down with bronze wool can work wonders. The wood is beyond my expertise but I've had success with reducing cracks by rubbing in repeated heavy applications of boiled linseed oil to restore moisture to the wood. Looks like you found a rewarding project and best of luck with it!
 
I like it a well-used combat rifle and we'll make a nice project for you. And I guarantee that screw won't come out do too old dirt or old grease gotten in those screw threads. My gunsmith had to take some time to get my trigger guard screw out of my kar98a carbine.

You should have seen that magazine housing when I got it out it was filthy
 
Damn nice rifle, - equally good photography, not too many get the main pictures I need in so few uploads... no messing around with irrelevant angles!

Regarding the BC, in this range it will be in front of the rear sight, as often as not above the stock, so disassembly might not be needed for the BC, though I would try to take it off just to be sure about the condition under the stock.

DWM made a lot of rifles in 1917, though far less than in 1916, - during 1917 DWM began its move away from rifles to focus on P08 and MG08's; it is probably why DWM bought WOK outright, to move rifle production out of their factory. Anyway, even Amberg made more G98's in 1917 than DWM, and DWM/17's are not especially common, probably 210-220k made that year, which sounds like a lot but really isn't for a war year. These two piece stocks are damn hard to find, DWM was one of the larger firms to use them, all known are 1916-1917 dated and they are not grouped together, they are interspersed throughout ranges with no pattern. So far as observations go, only the arsenals and MO/DWM used them, most known are DWM, but Erfurt is no slouch either. Oddly, some oldtimers attributed these to Danzig and Amberg, and they did use them late in production, especially Amberg, but DWM started early and in trends are more common.

Really a nice rifle you picked up!
 

Military Rifle Journal
Back
Top